31/8/2010· HDPE pipe and "transition" cement I''ve been using HDPE pipe and "transition" (between PVC and ABS) cement with decent results. Definitely far better than with the black ABS cement, which simply became brittle and flaked off the HDPE. The HDPE industry

Features of HDPE pipes and fittings: Green environmental protection: HDPE pipe non-toxic, tasteless, after strict health monitoring, belongs to green building materials, never scale, can effectively improve water quality. Corrosion resistance: HDPE pipelines are resistant to corrosion by a variety of chemical media, and chemicals present in the soil do not cause any degradation to the pipeline.

Specified Fittings provides custom HDPE pipe fittings to order. We also keep a variety of on-demand HDPE fittings in stock in Stevensville, MT, Early Branch, SC, and Longwood, FL. Our current HDPE inventory: Elbows 45 and 90 in DR7, DR9, DR11, and DR17

PVC can be joined to metal using a threaded PVC connector. The real problem is the HDPE duct. HDPE is common and cost effective conduit often used in directional boring. But PVC cement will not stick to HDPE at all. Mechanical coupling are available to

1 1/2" Shur-Lock II HDPE Coupling 1 1/2" Shur-Lock II HDPE Couplings by Duraline Features: 1.5" SDR, 1.9" ± .020" 1.335" One person installation Re-enterable, no special tools required Air and water tight No I.D. reduction Excellent pull out strength on hdpe, PVC

1" IPS HDPE Compression x 1" PVC SCH40 or SCH80 Compression Coupling NOT FOR GAS NOTE: GREY SIDE IS FOR PVC PIPES. BLUE SIDE IS FOR HDPE PIPE. ELOPRESS fittings are mechanical fittings to be used with high, medium and low density

supplier of plastic Pipes, Tanks, Fittings and Irrigation products, since 1998. Radical Investments (Pty) Ltd, trading as Flo-Tek Pipes & Irrigation was established in Botswana in 1998 manufacturing PVC pipes. In July 2003 and June 2004 Flo-Tek HDPE pipes

2.8 Transition Fitting – HDPE pipe to DI / PVC pipe A transition fitting is a mechanical assely of HDPE and PVC or DI pipe. The resulting product will allow a butt fusion joint on the HDPE end and standard PVC

PVC / HDPE Adapters Series 730 Transition for PVC/HDPE PVC IPS Sch.40/80 Series 731 Transition for PVC/HDPE Sch.35 Series 732 Transition for Ductile Iron Size PVC/HDPE Series 735 Transition for PVC/HDPE Series 737 ID Controlled PVC/HDPE Transition

HDPE, Inc. offers a full product line of transition fittings that provide connectivity between high-density polyethylene and other types of pipe materials. These fittings eliminate the need for labor consuming tie-rods, strapping and/or thrust blocking, keeping the pipe …

HDPE fittings refers to a range of jointing fittings and adaptors that suit HDPE pipe. These fittings are made from PE100 HDPE material, and are designed for HDPE pipelines. The large range and types of PE fittings reflects the versatility and adaptability of HDPE

Designed for use with smoothwall OD controlled innerduct (ASTM 3035), Sch. 40 and Sch. 80 innerduct, and is pressure tight to internal pressures above 200 psi when restrained or buried. Ideal for joining PE to PVC or threaded HDPE conduit.

Victaulic HDPE products are not intended for use on PVC pipe or other materials. Victaulic lubricant should not be used with HDPE pipe. Victaulic products for HDPE pipe are rated to pressures equal to the pipe with which they are used.

29/5/2016· There are no HDPE fittings that I came across, so I’d like to use PVC fittings if I can. Is there a glue that will glue/weld the two dissimilar materials? Or this being a system where water pressure is negligible, could just press fit the fittings together and then perhaps drive a few self tapping screws to hold the fitting to the pipe.

Used to transition from schedule 40, 80 or 120 PVC pipe to PEX, copper, CPVC, PE-RT or HDPE pipe without needing any special tools or glue. Available In UIP4008 1/2 in. CTS x 1/2 in. PVC

Fernco Flexible Couplings have found wide acceptance among sewer and pluing contractors and municipalities because of their quality and ease of installation. Fernco pipe couplings and adapters are used for all types of in-house and sewer connections: drain, waste, vent piping, house-to-main, repairs, cut- ins, conductor, roof drains and increasers-reducers.

2 · If you need to connect a high density polyethylene (HDPE) pipe to a polyvinyl chloride (PVC) pipe, you need to use a transition fitting to ensure a leak-proof seal between the two pieces of plastic pipe. Different types of plastic expand and contract at different rates.

HDPE Pipe Usebility Kuzeyboru Hdpe Pipes are easier to process, install and provide cost savings during construction. Structurally, other pipes tend to crack and break. Kuzeyboru Hdpe pipe (PE100) is designed to withstand the impact in the cold weather during Puhui Pipe manufacturer in China

* Shurjoint recommends the use of a silicone based lubricant for the HDPE series. H307 - ISO Size The Shurjoint Model H307 transition coupling provides for a fast, easy and direct transition from HDPE pipe and or fittings to grooved end HDPE pipe (IPS). Model

HDPE to PVC Transition Couplings Self-threading tapered threads on one side allows coupling on to HDPE. Other side threaded Part Nom. O.D. Std. Ctn. Std. Ctn.to PVC thread dimensions. No. Size (Duct Range) Qty. Wt. LS100 1" 1.21 – 1.41 100 25 LS125 1 Puhui Pipe manufacturer in China